| I just got my 450SLC back from having the timing chain, tensioner, camshaft oiler tubes and valve stem seals replaced. These are all jobs that any owner of a Mercedes V8 of this era will need to undertake at some point. The primary driver behind this was the need to replace the valve stem seals. A couple of my sparkplugs, #1 in particular, would regularly foul up. I didn’t have a lot of visible smoke, but I did see the odd puff of smoke taking off after a period idling. This is a pretty common problem in these engines. Age, and lack of use cause the valve stem seals to harden and allows oil to get into the cylinders, in particular at idle. A number of these engines have been prematurely rebuilt due to this simple issue. It also seemed sensible to change the timing chain at the same time. I understood that it had been done a year or so before I bought the car in 2003. I didn’t have any evidence for this. Removing the valve covers showed that the chain had been replaced at some point, as had the guides. However, I wasn’t sure the age of the chain and the guides were now coffee coloured. I started by ordering the parts I would need. The part numbers I ordered are listed below. I don’t guarantee these are correct for any other car. For a lot of these parts I prefer genuine given their importance to the engine and how expensive this job is. ![M117 450 Timing chain](https://live.staticflickr.com/65535/53634065787_7b620813f8_b.jpg)
- Timing chain – 000 997 76 94 – IWIS (In a Febi Box)
- Timing chain tensioner – 117 050 10 11 – Genuine. This is the tensioner with the port for air injection. It is quite expensive. The air injection system on my car has been disabled and it was not clear to me if I could have simply used the normal tensioner.
- Camshaft oiler tube kits x2 – 117 180 00 84 – I wanted genuine, but they are now NLA so purchased Febi.
- Chain guide x2 – 117 052 09 16 – Genuine
- Chain guide x2 – 117 052 08 16 – Genuine
- Tensioner guide – 117 050 04 15 – Genuine
- Guide pin – 116 052 21 74 – got a couple in case they were needed, but they can normally be reused.
- Left valve cover gasket – 116 016 13 21 – Elring
- Right valve cover gasket – 116 016 14 21 – Elring
- Valve cover copper sealing ring x8 – 915035 000016 – Reinz
- Valve stem seal kits x2 – 116 050 01 67 – Genuine
While I was there I also ordered some other parts I needed that will be used later, such as the drier pictured above. I also grabbed the two pictured air hoses to be replaced at the same time as they were rock hard. There were no major issues during the job, although my mechanic noted that the valve stem seals are much harder to do in the 107 than the 126. There is far less room, particularly up near the brake booster. The oil seals immediately showed why I had an issue with oil getting into the cylinders A couple had cracked and the rest were so hard they were not sealing properly. ![M117 450 Timing chain and valve stem seals](https://live.staticflickr.com/65535/53635404190_3775cec3cb_b.jpg)
It would appear that Mercedes-Benz revised these seals at some point. The new ones were rubber, whereas the old ones were a hard plastic type material. During the timing chain job, a couple of the lifters need replacement. Unlike during the timing chain job on my 560SEC, none of the guides were broken, but they were all discoloured. It is not clear how many kilometres were on my chain, but the camshaft sprockets had a reasonable amount of wear on them. After the job, my mechanic performed a compression test on my engine and he was very happy with the results, even after 313,000km. The car runs very well now, and seems to even have a little more power. This was quite an expensive job, but necessary if you are going to own a Mercedes-Benz v8 of this era.
In addition, during the timing chain job, I had the tensioner, guides, and camshaft oiler fittings replaced as per the parts list above. These should always be done at the same time. I’ve wanted to visit the Fox Collection in Melbourne for over 10 years. I used to have a job where I would commute to Melbourne twice a month but the opening hours never lined up with when I was there. This weekend I am traveling through Melbourne and happened to have the Saturday morning fee. I went along for the morning with my kids. The Fox Collection is a part of the personal collection of Lindsay Fox, an Australian trucking magnate. Lindsay Fox is now 87, and has been collecting these cars for years. As well as the public part of the collection, there are apparently another 300 or so cars out near Essendon Airport. The collection is housed in a heritage warehouse in the Melbourne Docklands area. This makes it very easy to get to. There is also plenty of parking if you are a local. The collection is housed over two floors. On the ground floor, there is a general room with high end cars on one side, and performance cars on the other. There are also a couple of trucks from the early years of Mr Fox’s trucking empire. ![The Fox Collection](https://live.staticflickr.com/65535/53620231439_ea13725e8a_b.jpg)
Additionally on the ground floor is the Ferrari Room. Upstairs there is a Mercedes-Benz room and a Porsche Room. Nearly all the cars are pretty special. In the general room you have cars like a Mercedes-Benz 540K Roadster (my favourite) along with an Derby Bentley and an Austin Healy 100S. The room also contains the only remaining Rolls Royce Camarge prototype. The Ferrari room contained an F40, F50, Enzo, 288GTO and a 246Dino. From this room I would take the 288GTO. Its not the most valuable, but the one I would like to drive. That assumes I would fit in. Upstairs the Porsche room has a collection of rare 356s as well as some other interesting cars from Porsche’s heritage and a few modern sports cars. In the Mercedes Benz room there is a Gullwing, a Pagoda, 190SL plus some very rare performance cars like a McLaren Mercedes, SL73, SLR and others. There is also one of only two AMG A38 cars, a twin engine version of the little city car. I would take the Gullwing. I enjoyed the Museum. About an hour is all you really need. The museum focuses on quality rather than quantity. Still, given there are around 300 extra cars, I think the could easily fit another 10-20 cars in the space at the docklands which would be a useful improvement to the museum. Regardless I would recommend the museum if you have an hour or so free in Melbourne on a Saturday morning or Thursday. One of my favourite day trip drive near Sydney is the Oberon to Goulburn Drive. I’ve done this drive in both directions and its a great mix of different roads, plus limited traffic. I even incorporated this road in my recent trip to Melborne. I had also seen that the parallel road that goes south out of Bathurst was also paved in the last 10 years. This road head south until it hits Crookwell, where you can either keep going south to Gunning, or veer off to Goulburn. ![](https://www.classicjalopy.com/wp-content/uploads/2024/03/BathurstGoulburn-1024x790.jpg)
I wanted to try this as another full day trip from Sydney, as well as have it as a candidate as part of bigger road trips. I had a full day free, so I got a small group of friends together and we went and tried it out. We met at McDonalds Lithgow. I took the back way there, via Galston Gorge, Maraylya and Bells Line of Road. This is a pretty good drive in itself and far better than the obnoxious Great Western Highway. We had three cars on our drive, my 560SEC a 380SEC and a W211. ![Bathurst to Goulburn](https://live.staticflickr.com/65535/53618107840_5da914af28_b.jpg)
From Lithgow, we left the main roads and headed towards Lake Lyell. This was quite a scenic spot and we continued past it towards O’Connell. Parts of this road were good and other parts were full of large potholes. We past the turn offs to Oberon which would have taken us on the normal road to Goulburn. We continued along towards George’s plain before heading south towards Tuena. The main part of the road south was pretty good. There was minimal traffic and it was quite scenic. We stopped for Lunch at the little coffee shop at Tuna before heading south towards Crookwell and Goulburn. We all really enjoyed the drive. If I had to pick, I would probably rate the Oberon – Goulburn road slightly better. However, the combination of both allows for an interesting possibility of doing a more adventurous day trip of avoiding the M31 and doing both roads in a single day. It would add another 100km and a few hours to the trip, but I think be worth it with an early start. I was pretty happy with my SEC performed on the trip. The owner of the 380SEC had just replaced his valve seals and that car was running better than ever. The W211 also made the trip without incident. It is probably one of the nicest series 1 W211s left in the country. This month’s night drive was a bit different. Instead of meeting up and doing a drive for 60-90 minutes, we did a very short drive and then went to check out the club library. I’ve been a member of the Mercedes Club for between 10 and 15 years. I knew the club had a library, and I heard it was pretty good, but I had never seen it. As the library was located in the club store room, this felt like a great night drive destination. The night drives are normally attended by around five to ten cars. This is the perfect number to go and check out something like the club library. In addition, the storage facility the club library is located would be largely deserted that late at night. The numbers would be too large to do a day run. ![meeting point for club library run](https://live.staticflickr.com/65535/53616653073_4d2c0e1b63_b.jpg)
I picked a month were our normal time was close to a long weekend. With double demerits on, it was a good time to do less driving. We met up at a 7/11 in Macquarie park. This was about a 20 minute drive from the club storage unit. It also allowed us to drive the Comenarra Parkway, one of the better roads in this area of Sydney. On the drive we had two 126s (my 560SEC and a 380SEC) two 123s (a 280CE and a 300D) plus a 108 280SE 3.5 and a 124 230E. Quite a good mix for a drive like this. On the night drives I try to avoid traffic lights and built up areas as its hard to keep the group together. This group of six was about as big as its feasible to do so. ![at the club library](https://live.staticflickr.com/65535/53616786539_10080ac2a6_b.jpg)
The drive was fairly uneventful, although we had an incredibly slow SUV in front of us the whole way along the Comenarra parkway. When we got to the club storage facility, we were quite impressed by the Club Library. The library is across four metal cabinets and its been arranged and catalogued at some point. There was a whole cabinet of workshop manuals, another of motoring books, a third one of magazines and Mercedes-Benz Brochures and the final one of club magazine back issues. ![Club Library](https://live.staticflickr.com/65535/53616652913_880505b89e_b.jpg)
The collection of workshop manuals and books was quite extensive. I could have stayed for a few hours to read. As we checked out the library, it was quickly apparent that the tree I parked under at the 7/11 was a roosting spot for birds as my car was covered in droppings. I had to do a makeshift cleaning job to ensure it didn’t ruin the paint. ![ruined paint7](https://live.staticflickr.com/65535/53616445201_4eefb510e2_b.jpg)
The choice of radio for my 1965 Mercedes 250SE Cabriolet was not an easy one. I don’t know what radio the car had in it’s early years. It is a diplomat delivery car, that was picked up from the factory in Stuttgart. The original radio would have either been a slimline model, or perhaps a radio delete plate. At some point, some butcher enlarged the opening and fitted a DIN radio. When I purchased the car it had a ghastly 90’s CD player. A few years ago, I removed the 90’s CD player and installed a Becker Tribute Radio. This is a modern radio that looks like an original Becker. However, when the alternator died it presumably damaged this radio and it was never the same. It did very strange things including sometimes running with the car switched off. Since it could drain the battery, I had to remove it. So there was not a gaping hole in the dash for the German car show last year, I quickly installed a Europa II Stereo from my Becker Collection as a temporary solution. The Europa II in question was a mid production radio. From its features it would have likely been manufactured between 1975 to 1977. It made a good temporary solution as it needed a service anyway, and the Europa II being a single piece radio, it was a quick install. After driving around for six months with the Europa II, it was clear that my car was no longer killing radios. It was therefore time for something more permanent. I could not install the correct radio due to the dashboard butchery, but I could install a DIN size Becker radio. In addition a friend suggested I use the knobs off a slimline radio that would match the car better. I ordered a set of those, and while I waited for them to arrive, went about thinking about which radio to install. My first option would have been a lovely Grand Prix mono from 1971. This radio is in superb cosmetic condition and the four band LMKUU markings would have fit in well with the age of the car. However, I would have needed to fit an external amplifier to drive four speakers. In addition, the auto seek ‘wunderbar’ feature is not working on this radio. Next option could have been a very early Becker Mexico. I have one of these from 1972 that could have worked. However a built in cassette isn’t right for a 1965 car since that didn’t come out until 1971. In addition, this early Mexico is a mono radio with a Stereo cassette player. As I wouldn’t have been using the cassette, only the radio, this seemed a worse choice than the Grand Prix Mono. Finally the other option was a Grand Prix Stereo. This was appealing as is a top of the line Stereo radio that seems to make sense for a car like a W111 Cabriolet. I have a couple of these radios, but the early ones need service. By far the best is a 1974 model Grand Prix Stereo I decided to go with this as it was in excellent condition. Being a 1974 model, it had the smaller amp that would be easier to fit, and I had already put the plugs on for the small amp, since that is what is built into the Europa II. I had this radio refurbished, so everything works. I could have used an earlier model, but the early Stereo radios have a balance wheel on the front, but that dates them to 1971-1972. In the photo below, it is sporting its original knobs. The only downside is the Grand Prix Stereo is a two piece radio with a separate amplifier like a Mexico cassette. ![Becker Grand Prix Stereo](https://live.staticflickr.com/65535/53607488446_9abdbdebd4_b.jpg)
The other Advantage of this radio was that I could plug in an external Bluetooth module into the port that normally would have accepted the external cassette player. This port accepts a Stereo signal. I tested the Bluetooth module on the bench and it works really well. It only interrupts the radio signal when you want to play music via Bluetooth, and it has a hands-free calling function too. In the photo below I am also testing the module in an earlier Becker Grand Prix Stereo. ![Becker Grand Prix stereo](https://live.staticflickr.com/65535/53607832439_730e6279fd_b.jpg)
One thing I had noticed from the Europa II was the whine coming from the speakers based on engine RPM. I purchased a radio noise filter from Jaycar to assist with the install. The actual installation was fairly straightforward. The Europa II came out pretty easily. I then wired in the noise filter and the separate amp for the Becker Grand Prix Stereo. I managed to use cable ties to hook the amplifier onto the heater box. The actual installation was fairly straightforward. Switched power and ground went into the noise filter. The noise filter the powered the radio. ![Noise filter](https://live.staticflickr.com/65535/53607948680_20a0d4e033_b.jpg)
I wouldn’t say the sound is perfect. For better sound I would need to replace speakers and use an external amplifier with a high pass filter like I have in the 560SEC. It does sound reasonable and looks great. The slimline knobs look great but were a pain to get on. Like the knobs on all the early radios they screw on rather than push on. It can be really hard to get the tiny screwdriver in when the radio is installed in the dash. Overall I am really happy with the install and how the radio looks in the dash. The slimline knobs make a huge difference. <
My 250SE Cabriolet had a feature I was not aware of. Underneath the injection pump is an oil/coolant heat exchanger. This was also an option on late 230SLs. Instead of a separate cooler that the M130 engined cars have, the heat exchanger helps warm up the oil when the engine is cool and cool it down when the engine is hot. There are lines from the oil filter housing that go to the heat exchanger, as well as coolant lines that come from the side of the block. An example is pictured below. The picture is not my heat exchanger. It is a second hand unit available on eBay. From all I read on the Pagoda forums, the M129 Heat Exchanger is quite effective. The 250SL runs quite cool with it. The heat exchanger is now NLA, but the part number is 000 188 44 01. ![M129 Heat Exchanger](https://www.classicjalopy.com/wp-content/uploads/2024/03/Capture-1024x318.jpg)
I would have been blissfully unaware of my heat exchanger except for a growing oil leak. The oil leak was coming from the braided flexible oil hose that runs from the far side of the M129 heat exchanger to the oil filter housing. When my mechanic investigated further, he also discovered that the coolant outlet on the engine block was corroded. I started looking up what parts I needed to buy to fix the oil leak and make sure the heat exchanger was working properly. On my car, the longer hose had a short metal section, the braided flexible hose and then another short metal section. But in the EPC this was one hard line. There was no mention of any other system. ![M129 Heat Exchanger](https://www.classicjalopy.com/wp-content/uploads/2024/03/2024-03-heat-exchanger.jpg)
I started doing some further research and I found a post on the W113 forum. It described how in the paper parts manual, there is an earlier setup which had been superseded. The older setup was never brought forward into the EPC. In that section you had the two hard lines (127 180 00 27 & 127 180 02 27) plus the braided line (198 180 01 82). This was replaced by 127 180 03 27 which was the single metal hose. 308 in the diagram above. In case you’re wondering 127 180 01 27 is the shorter hard line for the other outlet of the M129 Heat Exchanger (302). This never changed. While I had the backup of taking the existing braided hose to a hose shop to have the ends re-used for a new hose, I first checked to see what parts were still available. Since the braided house was first used on the 300SL, it is still available. The surrounding hard lines are not, but mine were perfectly fine. Additionally, the replacement part 127 180 03 27 is also still available. Neither were particularly expensive. Both are probably cheaper than having a hose company re-use the ends of my existing braided hose on a new one. I decided to go with the 300SL part. I had a few reasons for this. Firstly, there is very little space around the M129 Heat Exchanger. Getting a flexible hose in and connected with the engine in situ was probably going to be far easier. This was going to save me labour time. Secondly, the parts cost was less than half. Thirdly, I figured the flexible hose had a bit of give in it for vibrations and parts not being perfectly aligned after 60 years. And finally, I liked the idea of having 300SL parts on my car. ![M129 heat exchanger](https://live.staticflickr.com/65535/53597129306_2567a47b94_b.jpg)
While the car was at the workshop, I had new rear shocks fitted and the power steering pump adjusted so it wasn’t so noisy. My oil leak is gone. I’m also sure the heat exchanger working properly will help the car cool on very hot days. I also learned a lot about a feature of my car I never knew it had. Editors Note: This is part three in a series by Nick Gruzevskis about owning a Modern Mercedes convertible – in this case his R170 SLK230. The first part can be found here and the second part here. There are times when you feel like you’re making progress on a classic car and other times it just feels like you’re procrastinating. As I have just completed an interior, I was feeling positive, so decided to strike while the iron was hot. Since putting the interior back, I’d used the car on freeways several times and noticed the steering wheel shuttering from 90kph and above. I dropped car off to Donnellans, noting that front wheels likely needed a balance. I’d almost completed drinking my latte when I received text message communicating job was complete. First job done. I had been looking into replacing the original fabric wind deflector, not due to its condition, but rather as it was somewhat difficult to see out the rear with the top up. I had viewed the Pippins wind deflector some time ago, with most reviews being positive, but did note there were a few that commented on reflections. ![IMG_1302](https://live.staticflickr.com/65535/53581168022_40451c886c_b.jpg)
I ordered the R170 wind deflector with roll bar inserts on Feb 22nd and they arrived Mar 3rd, costing $415 AUD including delivery. The wind deflector is 8mm think smoke grey Perspex. You can opt to put a logo or design, but I choose not to do this, as I didn’t want anything impeding my vision. ![Pippins wind deflector](https://live.staticflickr.com/65535/53582478605_0bb2e062d5_b.jpg)
The rollbar inserts are made of the same smoke grey Perspex. Installation was quite simple, only tools you need is a Phillips screwdriver, removing the two screws that hold the hooks. It is tricky to install the deflector and put the two hooks back, took me about 30min to complete the job. The roll bar inserts are easier to get in, these just insert from the front of the car, inserting Perspex into top of rollbar, then compressing the roll bar material, pushing it into place. They are securely held in place by pressure/friction alone. ![Pippins wind deflector](https://live.staticflickr.com/65535/53582257213_69b2758471_b.jpg)
Testing for the first time, rear vision is dramatically improved. I’m not sure if wind buffeting , more testing is needed here, but looks a lot cleaner than the fabric deflector. The cons, apart from the cost, you do get some reflections from cars in front of you. It’s not really a deal breaker, just something to be aware of. ![Pippins wind deflector](https://live.staticflickr.com/65535/53581167967_f48fe56b91_b.jpg)
![Pippins wind deflector](https://live.staticflickr.com/65535/53582356984_66ef424a47_b.jpg)
Author: Nick Gruzevskis is a contributor to classicjalopy.com, and the custodian of a great collection of classic and modern cars. Links to some his other articles can be found here On my trip to Victoria last last year, the alternator on my 560SEC packed in. I was able to limp the car home by swapping batteries with a friend in another W126. I also purchased another battery on the road. When I arrived back in Sydney, it was this new battery that was still in the car. I was just going to leave that one there, until I noticed a slight creaking from the bonnet hinge. The bonnet was also a few mm too high. Turns out the new battery I bought along the way was slightly too big. It was fouling on the bonnet and putting pressure on the hinge. Since there was nothing wrong with the old battery, I decided to just put that one back in. In the photo, the one on the right is the new one. It’s a shame, because the new battery is brand new and a better spec. The other thing I wanted to fix was the battery tray had some surface rust, and the battery hold downs were missing. The battery hold downs may seem unimportant, but they prevent the battery shorting out on the bonnet or moving around over bumps or heavy cornering. They were also missing on my 560SEL.
I’ve previously repaired the battery trays on both my 450SLC and 560SEL. In both cases I used a rattle can primer and then top coat. I wasn’t especially happy with the result on either car. On the 450SLC, the top coat was too thick and ended up being soft. On the 560SEL I did two thin coats, and it was better, but the trays are not uniform and it was hard to get even coverage. I thought I would try something different this time. As before, I started with a wire wheel attachment for my drill to remove surface rust. I also used some brake clean to get some grease and residue off the tray. Surprisingly, the tray in the 560SEC was better than the one in the 560SEL. After a go with the wire brush, it actually came up reasonably well. The bottom was even better, the only real rust around where the ‘tongue’ attaches to the main body of the tray. I still thought there was value in doing this side regardless.
Instead of the rattle can, I decided this time to apply specific rust epoxy paint with a brush. This would result in a worse finish, but a much better application of the paint. Since the battery tray is really not visible with the battery installed, I thought this was a decent trade off.
I did two coats on the top and one on the bottom. My nine year old daughter enjoyed painting the 560SEC battery tray. I probably could have even used a product like miracle paint and had a better finish, but I didn’t have any, nor the time to drive to the supplier and get some. After two coats, the 560SEC battery tray looked quite a lot better, but it was of course obvious the paint had been applied with a brush.
I’ll see how it looks when I remove the battery next time. There is certainly a lot better all around coverage of the paint. While the battery tray was out, I vacuumed all the leaves out from underneath it. It is worth removing the battery tray every few years to remove any dirt and leaves from this part of the car. Getting the 560SEC battery tray back in the car was a bit fiddly, it was hard to get all three holes to line up.
In the end I had the tray in and it was a huge improvement to before. It’s still obvious it was painted with a brush, but there is no longer any rust or detritus. ![560SEC battery tray](https://live.staticflickr.com/65535/53580851060_d3b261446e_b.jpg)
Final step was to re-install the battery. While I was there, I installed a battery hold down. I had a couple on hand, a very rusty one from the 420SEL parts car, and a reasonable one that I found in the boot of the 560SEL after I ordered new ones. ![battery hold down](https://live.staticflickr.com/65535/53580623753_48b0b13368_b.jpg)
I’m not sure what I am going to do with that big Delkor battery. Off the top of my head, I don’t think it fits any car I have. I may try and sell it. It wasn’t cheap, but it did get me home. Today I went to a cars and coffee event at Gough Whitlam Park. It was organized by Enthusiast Insurance. I had been invited by a friend, and assumed it was a regular cars and coffee event that they were sponsoring. I think it was more an event for their customers. I’m not an Enthusiast customer, but it didn’t seem to matter a great deal. Gough Whitlam Park is the same location that is used for the annual German car show. It is a bit small for that event, but probably better suited to a simple cars and coffee. I would estimate around 100-200 cars were on display. Probably the lions share of those were modern modified and performance cars, but there were some interesting classics too. ![Enthusiast Insurance cars and Coffee](https://live.staticflickr.com/65535/53578158845_c59d78161e_b.jpg)
I took my 1965 250SE, primarily because it was the car I had at home on the day and it was a last minute decision to go. Given the wet and humid weather we’ve had in Sydney, it was the first time in months I’ve driven the car with the roof down. It was an interesting contrast to come to this event vs the normal cars and coffee events I go to. I still think St Ives is the best one in Sydney, but this was a nice way to start a Sunday morning and I was able to catch up with some friends. I recently drove down to Canberra in my 1965 250SE. This was the first time I had taken the car on a longish trip in a couple of years. The main reason for that was the running issue had been experiencing with the car over the last few years. I finally solved this issue last year by fitting a new electronic distributor. On the way down I noticed how bad the ride was. The car was quite bouncy and not very enjoyable to drive. While the car didn’t do any long trips, I was using it quite a bit on short trips to troubleshoot the running issues, so it seemed strange that the tyres would be flat spotted. I checked the pressures on the tyres and they were all fine, perhaps even a little higher than they needed to be. On the way back I had the same issue even after slightly reducing tyre pressure. I also noticed a crease on the tyre sidewall, it was very slight, but still noticeable. As the tyres were 8 years old this year, I had planned to change them anyway, so I decided to get a new set right away. I was worried that the tyres were starting to separate internally. On the last set of tyres, I made a mistake. Instead of looking up the original tyre size, I just replaced what was on the car. This was wrong. The tyres on the car were 195/70 R14. This was too low profile. Depending on the source, the tyres were originally either 185R14 or 195R14. The technical data book for 1966 says 185R14 and the Mercedes public archive says 195R14. They also have some old bias ply sizes. This is what it looks like my car was delivered with per the data card: 7.75 14 Continental. 185R14 is now a hard size to find. 195R14 isn’t hard to find in a light truck size, but almost impossible in a car size. Light truck tyres are not suitable for a classic luxury car, they are going to provide a terrible ride. However, 195/75 R14 is available in a few decent options. This is very close to the original size and in my view a pretty good alternative. I went with the Hankook Kinergy Eco 2 K435. This is the same tyre I have on my 450SLC, albeit in a different size. I’ve been quite happy with these tyres on my 107. ![tyres for my W111](https://live.staticflickr.com/65535/53562668019_45af993d23_b.jpg)
I went with five tyres in the end. The spare tyre pre-dated my ownership of the car. I couldn’t see a date code on it, and by the tread the tyre reckoned that from the tread it was from the late 70s or early 80s. It looked quite good, but I wouldn’t have wanted to drive very far on it. The tyre fitter also mentioned to me that one of the tyres had started to separate internally, so I’m glad I changed them. Tyres shouldn’t be used if older than about 8 years old and mine were getting up to that age later this year. As well as the tyres, I had the car aligned. I’ve have a few issues with the car feeling like its wandering at speed. I’ve had a few issues with older cars not being aligned against the right specs, so I photographed the relevant pages of the technical data book. since fitting, I’ve only driven the car a short distance, but the steering feels better. | |